What size mini split does a 800 sq ft bedroom in San Antonio, TX need?
800 ft² bedroom in San Antonio, TX
24,000BTU/hr
21,683 BTU/hr of load at 27.1 BTU/ft² — the figure for 3,566 cooling degree days
| Head size to buy | 24,000BTU/hr |
|---|---|
| Calculated load800 ft² × 27.1 BTU/ft² | 21,683BTU/hr |
| BTU per square foot hereinterpolated from San Antonio's 3,566 cooling degree days | 27.1BTU/ft² |
| What the 20 BTU/ft² rule givesthis room needs 36% more than the rule says | 16,000BTU/hr |
| Summer design temperature | 101°F |
| Winter design temperaturea mini split heats too — this is the number that decides whether it can carry the room alone | 28°F |
| Summer day–night swinga fairly dry climate | 20°F |
| Days at or above 90°F | 119days/yr |
| Oversize from the size stepwithin the normal step | 11% |
Notes
- The "20 BTU per square foot" rule is a Midwest number. San Antonio runs 3,566 cooling degree days, which works out to 27.1 BTU/ft² — so for this bedroom the rule is 36% short. A single national figure has to be wrong somewhere, and this is where.
- Bedroom: the room where oversizing hurts most — quiet, low load, long runtimes wanted.
- 24,000 BTU/hr sits close to the load, which is where a mini split works best. Inverter equipment is happiest running long and slow at part load; it is the short, hard cycles of an oversized head that leave a room cold and damp.
- San Antonio is fairly dry — summer nights stay within 20°F of the day's high, the signature of humid air. A meaningful share of this head's work is removing moisture, and it only removes moisture while it is running. This is the climate where an oversized head produces a room that reads cold and feels clammy.
- Do not forget the winter side. San Antonio designs to 28°F. That is mild enough that heating capacity is not the constraint here; size for cooling and the heating follows.
- Where these numbers come from. San Antonio International Airport, 12 km from downtown San Antonio, daily records 2015–2024. Design temperatures are calibrated against published ASHRAE values at eight airports and land within about 2°F of them.
The short answer
A 800 square foot bedroom in San Antonio, TX needs a head of about 24,000 BTU per hour. The calculated load is 21,683 BTU/hr.
Where that number comes from
San Antonio, TX runs 3,566 cooling degree days a year, which puts the room at 27.1 BTU per square foot rather than the 20 BTU/ft² the generic charts use. Applied to this room the rule gives 16,000 BTU/hr.
The winter half of the question
San Antonio, TX designs to 28°F. A mini split is a heat pump, and its heating capacity falls as the outdoor temperature drops — the nameplate is measured at 47°F, not at the temperature you actually need it.
Sizing a single room is not sizing a house
There is no other room to absorb a mistake. An oversized head short-cycles, never runs long enough to dehumidify, and leaves the room cold and damp.
Nearby sizes
- What size mini split does a 800 sq ft bedroom in Philadelphia, PA need?
- What size mini split does a 800 sq ft bedroom in San Diego, CA need?
- What size mini split does a 800 sq ft bedroom in Phoenix, AZ need?
- What size mini split does a 800 sq ft bedroom in Dallas, TX need?
- What size mini split does a 600 sq ft bedroom in San Antonio, TX need?
- What size mini split does a 800 sq ft living room in San Antonio, TX need?
Read more
- Sizing a Head for a Garage or WorkshopThe standard rule of thumb assumes a room inside a house. A garage is not one, and applying it gives a number that is too small.
- The Room Over the Garage — Why It Is Always Wrong and What Fixes ItEvery house with a room over the garage has the same complaint about it, and the reasons are structural rather than mechanical.
- Where the Head Goes Matters as Much as What Size It IsA wall-mounted head throws air in one direction, and the room is conditioned in that direction.
- Ductless or Central — What Each One Is Actually Good AtThe comparison is usually framed as efficiency. The real differences are distribution, control and what the house already has.