What size mini split does a 400 sq ft living room in Arlington, TX need?
400 ft² living room in Arlington, TX
12,000BTU/hr
11,347 BTU/hr of load at 25.8 BTU/ft² — the figure for 2,793 cooling degree days
| Head size to buy | 12,000BTU/hr |
|---|---|
| Calculated load400 ft² × 25.8 BTU/ft² × 1.1 for a living room | 11,347BTU/hr |
| BTU per square foot hereinterpolated from Arlington's 2,793 cooling degree days | 25.8BTU/ft² |
| What the 20 BTU/ft² rule givesthis room needs 29% more than the rule says | 8,800BTU/hr |
| Summer design temperature | 99°F |
| Winter design temperaturea mini split heats too — this is the number that decides whether it can carry the room alone | 20°F |
| Summer day–night swinga moderately humid climate | 19°F |
| Days at or above 90°F | 88days/yr |
| Oversize from the size stepwithin the normal step | 6% |
Notes
- The "20 BTU per square foot" rule is a Midwest number. Arlington runs 2,793 cooling degree days, which works out to 25.8 BTU/ft² — so for this living room the rule is 29% short. A single national figure has to be wrong somewhere, and this is where.
- Living room: more people, more glazing, more electronics. The 1.1× factor accounts for that.
- 12,000 BTU/hr sits close to the load, which is where a mini split works best. Inverter equipment is happiest running long and slow at part load; it is the short, hard cycles of an oversized head that leave a room cold and damp.
- Arlington is moderately humid — summer nights stay within 19°F of the day's high, the signature of humid air. A meaningful share of this head's work is removing moisture, and it only removes moisture while it is running. This is the climate where an oversized head produces a room that reads cold and feels clammy.
- Do not forget the winter side. Arlington designs to 20°F. A cold-climate rated head will hold most of its capacity there, but a standard one will not — ask for the capacity at 20°F in writing.
- Where these numbers come from. Fort Worth, 21 km from downtown Arlington, daily records 2015–2024. Design temperatures are calibrated against published ASHRAE values at eight airports and land within about 2°F of them.
The short answer
A 400 square foot living room in Arlington, TX needs a head of about 12,000 BTU per hour. The calculated load is 11,347 BTU/hr.
Where that number comes from
Arlington, TX runs 2,793 cooling degree days a year, which puts the room at 25.8 BTU per square foot rather than the 20 BTU/ft² the generic charts use. Applied to this room the rule gives 8,800 BTU/hr.
The winter half of the question
Arlington, TX designs to 20°F. A mini split is a heat pump, and its heating capacity falls as the outdoor temperature drops — the nameplate is measured at 47°F, not at the temperature you actually need it.
Sizing a single room is not sizing a house
There is no other room to absorb a mistake. An oversized head short-cycles, never runs long enough to dehumidify, and leaves the room cold and damp.
Nearby sizes
- What size mini split does a 400 sq ft living room in Wichita, KS need?
- What size mini split does a 400 sq ft living room in Bakersfield, CA need?
- What size mini split does a 400 sq ft living room in Minneapolis, MN need?
- What size mini split does a 400 sq ft living room in Cleveland, OH need?
- What size mini split does a 300 sq ft living room in Arlington, TX need?
- What size mini split does a 500 sq ft living room in Arlington, TX need?
- What size mini split does a 400 sq ft bedroom in Arlington, TX need?
Read more
- Mini Split Blowing Cold Air in Heat Mode — Defrost, UsuallyEvery air-source heat pump does this. Knowing what a defrost cycle looks like is the difference between waiting ten minutes and calling somebody out.
- Mini Split Leaking Water Indoors — Four Causes, One CommonA cooling head makes a couple of litres a day. It leaves through a small pipe with no pump behind it, and that pipe is where nearly every leak starts.
- Multi-Zone Mini Split Not Cooling Every Room — The Minimum Output ProblemThe system is not underpowered. It is oversized for the one room that is calling, and multi-zone units handle that far worse than single-zone ones.